Language Key Not Found
Language Key Not Found (1)
Language Key Not Found- SIRIUS
- SBOX
- R1DB/R2DB
- R3
- R4
- R8
- MINITAURs
- DEWE-43A
- SIRIUS MINI
- SIRIUS waterproof
- SBOX waterproof
- KRYPTON
- KRYPTON CPU
- R8rt
- IOLITE
- CAN interfaces
- GPS and IMU devices
- Aerospace interfaces
- Video cameras
- Current transducers
- Accelerometers & angle sensors
- Dewesoft X3
- DSI adapters
- EtherCAT accessories
- Battery packs
- Displays
- Mounting plates
Thanks for contacting us. One of our specialists will get in touch as soon as possible.




General system specifications
Counter specification
Counter | |
Timebase | 102.4MHz |
Time base accuracy Typical | 5 ppm, Max: 20 ppm |
Max. Bandwidth | 10MHz |
Input Filter | 500 ns, 1μs, 2μs, 4μs, 5μs and 7.5μs |
Input Level Compatibility | TTL (Low: <0.8, High > 2V) |
Input Impedance | 100kΩ pull-up to +3.3V |
Input Protection | ±25Volt continuous |
Alarm output | Open collector, max. 100mA/30Volt |
Sensor supply | 5V/100mA;12V/50mA |
CAN specification
CAN bus | |
Number of ports | 1 |
Interface type | CAN 2.0B, up to 1 MBit/sec |
Special applications | CCP, OBDII, J1939, CAN output |
Galvanic isolation | Isolated (only on isolated motherboard) |
Bus pin fault protection | ±36V |
ESD protection | 8kV |
Dual core amplifiers
Dual core amplifiers
High density amplifiers
High speed amplifiers
Overview
STG | STGM | ACC | CHG | HV | LV | |
Connectors | DB9, L2B7f, L2B10f | DB9, L2B7f, L2B10f | BNC, TNC | BNC, TNC | BANANA | DB9, BNC, BANANA |
Counter version | ||||||
Channels per slice | 8 | |||||
Data rate / channel | 200 kHz USB, 20 kHz Ethercat | |||||
Resolution | 24 bit dual core | |||||
Bandwidth | 70 kHz | |||||
Voltage ranges | ±50V, ±10V, ±1V, ±100mV | ±10V, ±1V, ±100 mV, ±10 mV | ±10 V, ±50 mV | ±10V, ±500 mV | ±1200 V, ±50 V | ±200V, ±20V, ±10V, ±1V, ±100 mV |
Input coupling | DC, AC 1Hz (3, 10 Hz SW) | DC, AC 1Hz (3, 10 Hz SW) | DC, AC 1Hz (3, 10 Hz SW) | DC, AC 0.1 Hz, 1 Hz, 10 Hz, 100 Hz | DC | DC, AC 1Hz (3, 10 Hz SW) |
Sensor excitation | 0..20 V max. 0.8W, 0..60mA max 0.5W | 0..15V max. 44mA | IEPE 2,4,8,12,16, 20 mA |
IEPE 4,8,12 mA | 2..30 V bipolar, 0..24 unipolar, max. 0.2A/2W | |
Bridge connection | Full, ½, ¼ 350Ω, ¼ 120Ω 3, 4 wire | Full, ½, ¼ 350Ω, ¼ 120Ω 3 wire | Full | |||
Programmable shunt | 59.88 kΩ, 175kΩ bipolar | 100 kΩ bipolar | ||||
IEPE input | DSI-ACC | DSI-ACC | DSI-ACC | |||
Resistance | DSI20mA, DSI5A | DSI20mA, DSI5A | ||||
Temperature (PTx) | DSI-RTD | DSI-RTD | ||||
Thermocouple | DSI-TH | DSI-TH | DSI-TH | |||
Potentionemeter | Yes | ??? | ||||
LVDT | DSI-LVDT | DSI-LVDT | DSI-LVDT | |||
Charge | DSI-CHG | DSI-CHG | 100k, 10k pC | DSI-CHG | ||
Current | ext. shunt | ext. shunt | ext. shunt | ext. shunt | ext. shunt | |
TEDS | ||||||
Isolation voltage | 1000 V | 1000 V | 1000 V | 1000 V | CATII 1000V | 1000 V |
Power consumption per channel | 2W/ch | 1.3W/ch | 1 W/ch | 1.2W/ch | 1W/ch | 1.2W/ch |
Advanced functions | Supports all strain types and high input range | Low power, sensor and amplifier balance, bipolar shunt | Sensor error detection, high dynamic range | Sensor error detection in IEPE and CHG mode (injection) | High voltage, high isolation | High sensor power and multi range |
STG specifications
Inputs | ||||
Input types | Voltage Full/Half/Quarter bridge strain (120Ω and 350Ω) Current (ext. Shunt) |
|||
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |||
Sampling Rate | Simultaneous 200kS/sec | |||
Dual Core Ranges (Low) | ±10V (±500mV) | ±1V (50mV) | ±100mV (±5mV) | ±10mV (±0.5mV) |
Gain accuracy | ±0.05% of reading | |||
Offset accuracy (Dual Core) | ±5 (2) mV | ±0.5 (0.2) mV | ±0.1 (0.1) mV | ±0.1 (0.1) mV |
Typ. Dynamic Range@10kS (Dual Core) |
137 dB (152 dB) | 137 dB (147 dB) | 130 dB (132 dB) | 112 dB (112 dB) |
Typ. SNR@10kS (Dual Core) | 105 dB (121 dB) | 104 dB (111 dB) | 95 dB (95 dB) | 75 dB (75 dB) |
Typ. CMR @ DC...50Hz/400Hz/1kHz | 88/86/84 dB | 97/96/95 dB | 111/110/102 dB | 111/110/102 dB |
Gain Drift Typical | 10 PPM/K, max. 40 PPM/K | |||
Offset Drift Typical | 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec) | |||
Channel Cross talk | 120 dB @ 10kHz | |||
Input Coupling | DC | |||
Input Impedance | 10 MΩ | |||
Max. Common Mode Voltage | Isolated version: ±500 V | |||
Differential version: ±12 V | ||||
Overvoltage Protection | In+ to In-: 50 V continuous; 200V peak (10msec) | |||
Excitation Voltage | ||||
Excitation Voltage | Free programmable (16 Bit DAC) | |||
Predefined levels | 0, 1, 2.5, 5, 10 and 15 VDC | |||
Accuracy | ±0.05 % ±2 mV | |||
Drift | ±50 ppm/K ±100 μV/K | |||
Load stability | 0% to 100% load <0.01% | |||
Noise @ 10V/350Ω | < 150 μVrms@10 kS | |||
Line regulation over 20Ω of change | < 0.005% @ 120Ω load | |||
Sense Impedance to Exc / to GND | 100 kΩ / > 100 MΩ | |||
Current limit | 45mA | |||
Protection | Continuous short to ground | |||
Bridge Connection Types | ||||
Bridge types | Full//Half/Quarte/ bridge (3-wire) | |||
Ranges | 2mV/V…1000mV/V free programmable with Dual Core | |||
Internal Bridge Completion | Half bridge 1 kΩ Quarter bridge 120Ω and 350Ω |
|||
Typ. Bridge Completion Accuracy | 0.05 %; TCR: 5 ppm/K (others on request) | |||
Internal Shunt Resistor | 59.88 kΩ, 175 kΩ, software selectable (others on request) | |||
Typ. Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | |||
Input Short, Sensor Offset Adjust | Software selectable | |||
Counters (only on STG+ type) | ||||
Inputs | 1 digital counter input 3 digital inputs Fully synchronised with analog data Alarm output |
|||
Counter Modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
General Counter Specifications | See "SIRIUS counter specifications" | |||
Additional Specifications | ||||
Input connector | DSUB - 9, Lemo2B 8pin, Lemo2B 16pin (others on request) | |||
TEDS support | Standard + DSI® adapters |
STGM specification
Inputs | ||||
Input types | Voltage Full/Half/Quarter bridge strain (120Ω and 350Ω) |
|||
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |||
Sampling Rate | Simultaneous 200kS/sec | |||
Dual Core Ranges (Low range) | ±10V (±500mV) | ±1V (50mV) | ±100mV (±5mV) | ±10mV (±0.5mV) |
Gain accuracy | ±0.05% of reading | |||
Offset accuracy (Dual Core) | ±5 (2) mV | ±0.5 (0.2) mV | ±0.1 (0.1) mV | ±0.1 (0.1) mV |
Offset accuracy after Balance Amplifier | 0.2mV | 0.02mV | 0.02mV | 0.02mV |
Typ. Dynamic Range@10kS (Dual Core) | 137 dB (152 dB) | 137 dB (147 dB) | 130 dB (132 dB) | 112 dB (112 dB) |
Typ. SNR@10kS (Dual Core) | 105 dB (121 dB) | 104 dB (111 dB) | 95 dB (95 dB) | 75 dB (75 dB) |
Typ. CMR @ DC...50Hz/400Hz/1kHz | 88/86/84 dB | 97/96/95 dB | 111/110/102 dB | 111/110/102 dB |
Gain Drift | Typical 10 PPM/K, max. 40 PPM/K | |||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec) | |||
Channel Cross talk | 120 dB @ 10kHz | |||
Input Coupling | DC | |||
Input Impedance | 10 MΩ | |||
Max. Common Mode Voltage | Isolated version: ±500 V | |||
Differential version: ±12 V | ||||
Overvoltage Protection | In+ to In-: 50 V continuous; 200V peak (10msec) | |||
Excitation Voltage | ||||
Excitation Voltage | Free programmable (16 Bit DAC) | |||
Predefined levels | 0, 1, 2.5, 5, 10 and 15 VDC | |||
Accuracy | ±0.05 % ±2 mV | |||
Drift | ±50 ppm/K ±100 μV/K | |||
Load stability | 0% to 100% load <0.01% | |||
Noise @ 10V/350Ω | < 150 μVrms@10 kS | |||
Line regulation over 20Ω of change | < 0.005% @ 120Ω load | |||
Sense Impedance | 100 kΩ to Exc / > 100 MΩ to GND | |||
Current limit | 45mA | |||
Protection | Continuous short to ground | |||
Bridge Connection Types | ||||
Bridge Types | Full/Half/Quarter bridge (3-wire) | |||
Ranges | 2mV/V…1000mV/V free programmable with Dual Core | |||
Internal Bridge Completion | ½ bridge 1 kΩ and ¼ bridge 120Ω and 350Ω | |||
Typ. Bridge Completion Accuracy | 0.05 %; TCR: 5 ppm/K (others on request) | |||
Internal Shunt Resistor | 100 kΩ, software selectable (others on request) | |||
Typ. Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | |||
Input Short, Sensor Offset Adjust | Software selectable | |||
Counters (only on STGM+ type) | ||||
Inputs | 1 digital counter input 3 digital inputs Fully synchronised with analog data Alarm output |
|||
Counter Modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
General Counter Specifications | counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
Additional Specifications | ||||
Input connector | DSUB9, Lemo2B 8pin, Lemo2B 16pin (others on request) | |||
TEDS support | Standard + DSI® adapters |
ACC specification
Inputs | ||
Input types | Voltage IEPE |
|
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |
Sampling Rate | Simultaneous 200kS/sec | |
Ranges (Dual Core Low Range) | ±10V (±500mV) | ±500mV (NA) |
Input Accuracy (Dual Core) | ±0.1% of reading ±10(1)mV | ±0.1 of reading ±1(NA)mV |
Dynamic Range@10kS (Dual Core) | 140 dB (160 dB) | 135 dB (NA) |
Typ. SNR@50kS (Dual Core) | 107 dB (125 dB) | 100 dB (NA) |
Typ. CMR @ 50Hz/1kHz | 140/120 dB | 140/120 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |
Offset Drift | Typical 0.5 μV/K + 2 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |
Gain Linearity | <0.02% | |
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec) | |
Channel Cross talk | >160 dB @ 1kHz | |
Input Coupling | DC, AC 0.1 Hz,1Hz | |
Input Impedance | 1 MΩ (270kΩ for AC coupling ≥ 1Hz)in parallel with 100pF | |
Overvoltage Protection | In+ to In-: 50 V continuous; 200V peak (10msec) | |
IEPE mode | ||
Excitation | 2, 4, 8, 12, 16 or 20mA | |
Compliance voltage | 25 Volt | |
Output Impedance | >100 kΩ | |
Sensor detection | Shortcut: <4Volt; Open: > 19Volt | |
Counters (ACC+ type only) | ||
Inputs | 1 digital counter input 3 digital inputs Fully synchronised with analog data |
|
Counter Modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |
General Counter Specifications | See "SIRIUS counter specifications" | |
Additional Specifications | ||
Input connector BNC | BNC | |
TEDS support | IEPE mode only |
CHG specification
Inputs | ||
Input types | Voltage IEPE Charge |
|
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |
Sampling Rate | Simultaneous 200kS/sec | |
Ranges (Dual Core Low Range) | ±10V (500mV) | ±500mV (NA) |
Input Accuracy (Dual Core) | ±0.05% of reading ±5 (0.5) mV | ±0.05 of reading ±0.5 mV |
Typ. Dynamic Range@10kS (Dual Core) | 140 dB (155 dB) | 130 dB (NA) |
SNR@50kS (Dual Core) | 107 dB (124 dB) | 98 dB (NA) |
Typ. CMR @ 50 Hz/1 kHz | 140 dB/120 dB | 140 dB/120 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |
Offset Drift | Typical 1 μV/K + 5 ppm of range/K, max 5 μV/K + 10 ppm of range/K | |
Gain Linearity | <0.02% | |
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec) | |
Channel Cross talk | 180 dB @ 50Hz; 160 dB @ 1kHz | |
Input Coupling | DC, AC (0.1 Hz, 1 Hz, 10 Hz or 100 Hz) | |
Input Impedance | 1 MΩ in parallel with 100pF | |
Overvoltage Protection | In+ to In-: 50 V continuous; 200V peak (10msec) | |
IEPE mode | ||
Excitation | 4, 8 or 12 mA | |
Compliance voltage | 25 Volt | |
Output Impedance | >100 kΩ | |
Sensor detection | Shortcut: <4 Volt; Open: > 19Volt | |
Charge ranges (Low Range) | ±100 000 pC (5000 pC) | ±10 000 pC (500 pC) |
Input accuracy (HPF 0.1Hz) | ±0.5% of reading ±20 pC | ±0.5% of reading ±5 pC |
Dynamic Range@10kS (Dual Core) | 130 dB (150 dB) | 120 dB (140dB) |
SNR@50kS (Dual Core) | 107 dB (120 dB) | 105 dB (118 dB) |
Input coupling | 0.01 Hz, 0.03 Hz, 0.1 Hz, 0.5 Hz, 1 Hz, 10 Hz or 100 Hz |
|
Charge injection | 1Vrms, 20 Hz, 0.5% accuracy | |
Counters (only in CHG+ type) | ||
Inputs | 1 digital counter input 3 digital inputs Fully synchronised with analog data |
|
Counter modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |
General counter specifications | See "SIRIUS counter specifications" | |
Additional specifications | ||
Input connector | BNC or TNC (others on request) | |
TEDS support | IEPE mode only |
HV specification
Inputs Voltage | ||
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |
Sampling Rate | Simultaneous 200kS/sec | |
Ranges (Dual Core Low Range) | ±1200V (±50V) | ±50V (NA) |
Gain accuracy | ±0.05% of reading | |
Offset accuracy (Dual Core) | ±100 (50) mV ±50 mV | |
Typ. Dynamic Range@10kS (Dual Core) | 142 dB (158 dB) | 132 dB (NA) |
Typ. SNR@50kS (Dual Core) | 107 dB (120 dB) | 95 dB (NA) |
Typ. CMR @ 50Hz/1kHz | 85/60 dB | 85/60 dB |
Gain Drift | Typical 5 ppm/K, max. 30 ppm/K | |
Offset Drift | Typical 1 mV/K + 1 ppm of range/K, max 2 mV/K + 5 ppm of range/K | |
Gain Linearity | <0.02% | |
Inter Channel Phase-mismatch | 0.04° * fin [kHz] + 0.2° (@ 200 kS/sec) | |
Channel Cross talk | 115 dB @ 50Hz; 90 dB @ 1kHz | |
Input Coupling | DC | |
Input Impedance | 10 MΩ || 2pF | |
Protection class | CAT III 600 V; CAT II 1000 V | |
Overvoltage Protection | In+ to In-: 1.8 kVRMS, Inx to GND: 1.4kVRMS) | |
Additional Specifications | ||
Input connector | Banana | |
TEDS support | Not availaable |
LV specification
Inputs | ||||
Input types | Voltage Full bridge strain |
|||
ADC Type | 24bit delta-sigma dual core with anti-aliasing filter | |||
Sampling Rate | Simultaneous 200kS/sec | |||
Dual Core Ranges (Low Range) | ±200V (10 V) | ±10V (500 mV) | ±1V (50 mV) | ±100mV (5 mV) |
Gain accuracy | ±0.05% of reading | |||
Offset accuracy (Dual Core) | ± 40 (20) mV | ±2 (1) mV | ± 0.2 (0.2) mV | ± 0.1 (0.1) mV |
Offset accuracy after Balance Amplifier | 2mV | 0.1mV | 0.02mV | 0.01mV |
Typ. Dynamic Range@10kS (Dual Core) | 136 dB (146 dB) | 137 dB (152 dB) | 137 dB (147 dB) | 130 dB (132 dB) |
Typ. SNR@10kS (Dual Core) | 109 dB (118 dB) | 109 dB (126 dB) | 109 dB (116 dB) | 97 dB (97 dB) |
Typ. CMR @ 50Hz/400Hz/1kHz/10kHz | 70/70/60/55 dB | 95/95/89/84 dB | 105/105/100/95 dB | 115/112/107/102 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |||
Offset Drift | Typical 0.3 μV/K + 5ppm of range/K, max: 2 μV/k + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec and 10 V range) | |||
Channel Cross talk | 120 dB @ 10kHz (range ≤ 10 V); 95 dB @ 10kHz (range = 100V) | |||
Input Coupling (see 1) | DC, AC 1Hz (3 Hz, 10 Hz per SW) | |||
Input Impedance | 200 V Range: 1 MΩ; all other ranges 10 MΩ between IN+ or In- against GND | |||
Max. common mode voltage | Isolated version ±500 V | |||
Differential version: 200 V range: ±200 V; all other Ranges: ±12 V | ||||
Input Overvoltage Protection | 200 V Range: 300 V; all other ranges: 100 V (250 V peak for 10 msec) | |||
Excitation Voltage | ||||
Excitation voltage | Unipolar or Bipolar Software selectable (programmable with 16 Bit DAC) | |||
Excitation Level unipolar | 0 .. 24 Volt; Predefined levels: 1, 2.5, 5, 10, 12, 15, 20 and VDC | |||
Excitation Level bipolar | 2 .. 30 Volt; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC | |||
Accuracy | ±0.1 % ±5 mV | |||
Drift | ±50 ppm/K ±100μV/K | |||
Stability | 10% to 90% load (bipolar) < 0.01% | |||
Current limit | 200 mA (2 Watt max. per channel, 12 Watt max. per Slice) | |||
Protection | Continuous short to ground | |||
Bridge connection types | ||||
Bridge type | Full bridge | |||
Ranges @ 10 Vexc(low range) | 2mV/V…1000mV/V free programmable with Dual Core | |||
Input short, Sensor offset adjust | Software selectable | |||
Counters (only on LV+ type) | ||||
Inputs | 1 digital counter input 3 digital inputs Fully synchronised with analog data Alarm output |
|||
Counter modes | Counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
General Counter Specifications | See "SIRIUS counter specifications" | |||
Additional Specifications | ||||
Misc function | Excitation control monitoring, Amplifier Short, Single Ended/Differential | |||
Input connector | DSUB 9, BNC, Banana (others on request) | |||
TEDS support | Standard + DSI® adapters | |||
1) In- must be within ±10V referred to GND(iso); for Ranges >10 V the DC value of In- is not rejected |
Overview
HD-STGS | HD-LV | HD-ACC | |
Connectors | DB9, L1B10f | DB9, BNC | BNC |
Counter version | |||
Channels per slice | 16 | ||
Data rate / channel | 200 kHz USB, 10 kHz Ethercat | ||
Resolution | 24 bit | ||
Bandwidth | 70 kHz | ||
Voltage ranges | ±10V, ±1V, ±100 mV, ±10 mV | ±100V, ±10V, ±1V, ±100 mV | ±10 V, ±5V, ±1V, ±200mV |
Input coupling | DC | DC | DC, AC 0.1 Hz, 1Hz (3, 10 Hz SW) |
Sensor excitation | 0..12V max. 44mA | 2..30 V bipolar, 0..24 unipolar, max. 0.2A/2W |
IEPE 4,8,12 mA |
Bridge connection | Full, ½, ¼ 350Ω, ¼ 120Ω 3 wire | Full | |
Programmable shunt | 100 kΩ | ||
IEPE input | DSI-ACC | DSI-ACC | |
Resistance | DSI20mA, DSI5A | DSI20mA, DSI5A | |
Temperature (PTx) | DSI-RTD | DSI-RTD | |
Thermocouple | DSI-TH | DSI-TH | |
Potentionemeter | Yes | ??? | |
LVDT | DSI-LVDT | DSI-LVDT | |
Charge | DSI-CHG | DSI-CHG | |
Current | ext. shunt | ext. shunt | ext. shunt |
TEDS | |||
Isolation voltage | 500 V in pairs | 500 V in pairs | 500 V in pairs |
Power consumption per channel | 1.3W/pair | 1.3W/pair | 1.3 W/pair |
Advanced functions | Low power, sensor and amplifier balance | High sensor power and multi range | Sensor error detection |
HD-STGS specification
Inputs | Voltage, full bridge strain, half bridge strain, quarter bridge strain (120Ω and 350Ω) | ||||
ADC Type | 24bit delta-sigma with anti-aliasing filter | ||||
Sampling Rate Simultaneous | 200kS/sec | ||||
Ranges | ±10V | ±1V | ±100mV | ±10mV | error in manual (dual core is mentioned) |
Gain Accuracy | ±0.05% of reading | ||||
Offset Accuracy | ±2mV | ±0.2mV | ±0.1mV | ±0.1mV | |
Offset Accuracy after Balance Amplifier |
±0.2mV | ±0.02mV | ±0.01mV | ±0.01mV | |
Dynamic Range@10kS | 137 dB | 137 dB | 130 dB | 112 dB | |
Typ. SNR@10kS | 104 dB | 95 dB | 75 dB | ||
Typ. CMR @ 400 Hz/1 kHz | 86/84 dB | 96/95 dB | 112/102 dB | 112/102 dB | |
Gain Drift | Typical 10 PPM/K, max. 40 PPM/K | ||||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | ||||
Gain Linearity | <0.02% | ||||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec) | ||||
Channel Cross talk | 120 dB @ 10kHz | ||||
Input Coupling | DC | ||||
Input Impedance | 10 MΩ | ||||
Max. common mode voltage | ±12 V | ||||
Overvoltage Protection | In + to In-: 50 V continuous; 200V peak (10msec) | ||||
Excitation Voltage | Free programmable (16 Bit DAC) | ||||
Predefined levels | 0, 1, 2.5, 5, 10 and 12 VDC | ||||
Accuracy | ±0.05 % ±2 mV | ||||
Drift | ±50 ppm/K ±100 μV/K | ||||
Stability 10% to 90% load | <0.01% | ||||
Current limit | 45mA (200mW max. Power) | ||||
Protection | Continuous short to ground | ||||
Bridge Connection Types | Full bridge, ½ bridge, ¼ bridge (3-wire) | ||||
Ranges | 2mV/V…1000mV/V free programmable | ||||
Internal Bridge Completion | ½ bridge and ¼ bridge 120Ω and 350Ω | ||||
Bridge Completion Accuracy | 0.05 %; TCR: 5 ppm/K (others on request) | ||||
Internal Shunt Resistor | 100 kΩ (others on request) | ||||
Typ. Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | ||||
Input Short, Sensor Offset Adjust | Software selectable | ||||
Additional Specifications | |||||
Input connector | DSUB9 | missing... | |||
TEDS support | Standard + DSI® adapters |
HD-LV specification
Inputs | Voltage, full bridge strain | |||
ADC Type | Type 24bit delta-sigma with anti-aliasing filter | |||
Sampling Rate | Simultaneous 200kS/sec | |||
Ranges | ±100V | ±10V | ±1V | ±100mV |
Gain accuracy | ±0.05% of reading | |||
Offset accuracy | ± 20 mV | ± 2 mV | ± 0.2 mV | ± 0.1 mV |
Dynamic Range@10kS | 134 dB | 137 dB | 137 dB | 125 dB |
Typ. SNR@10kS | 104 dB | 104 dB | 104 dB | 95 dB |
Typ. CMR @ 400 Hz/1 kHz | 74/70 dB | 86/84 dB | 96/95 dB | 112/102 dB |
Gain Drift | Typical 10 PPM/K, max. 40 PPM/K | |||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec and 10 V Range) | |||
Channel Cross talk | 120 dB @ 10kHz (Range ≤ 10V); 76dB @ 1kHz (Range = 100V) | |||
Input Coupling | DC | |||
Input Impedance | 1 MΩ for 100V Range; all other Ranges10 MΩ | |||
Max. common mode voltage | 100V Range: ±100 V; all other Ranges: ±12 V | |||
Overvoltage Protection | In+ to In-: 100V Range: 200V; all other Ranges: 50V (200V for 10msec) | |||
Excitation Voltage | Unipolar or Bipolar Software selectable (programmable with 16 Bit) | |||
Excitation Level unipolar | 0 .. 24 Volt; Predefined levels: 1, 2.5, 5, 10, 12, 15, 20 and 24 VDC | |||
Exication Level bipolar | 2 .. 30 Volt; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC | |||
Accuracy | ±0.1 % ±5 mV | |||
Drift | ±50 ppm/K ±100 μV/K | |||
Stability 10% to 90% load | <0.01% | |||
Current limit | 100mA (1 Watt max. per Channel, 12 Watt max. per Slice) | |||
Protection | Continuous short to ground | |||
Bridge Connection Types | Full bridge | |||
Ranges @ 10VExc | 2mV/V…1000mV/V free programmable | |||
Sensor Offset Adjust | Software selectable | |||
Additional Specifications | ||||
Input connector | DSUB9, BNC (others on request) | |||
TEDS support | Standard + DSI® adapters |
HD-ACC specification
Inputs | Voltage, IEPE | |||
ADC Type | Type 24bit delta-sigma with anti-aliasing filter | |||
Sampling Rate | Simultaneous 200kS/sec | |||
Ranges | ±10 V | ±5 V | ±1 V | ±200 mV |
Gain accuracy | ±0.05% of reading |
|||
Offset accuracy | ±2 mV | ±1 mV | ±0.2 mV | ±0.1 mV |
Typ. Dynamic Range@10kS | 137 dB | 137 dB | 137 dB | 131 dB |
Typ. SNR@10kS | 109 dB | 109 dB | 108 dB | 102 dB |
Typ. CMR @ 400 Hz/1kHz | 140/120 dB | |||
Gain Drift | Typical 10 PPM/K, max. 30 PPM/K | |||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° (@ 200 kS/sec and 10 V Range) | |||
Channel Cross talk | 150 dB @ 50Hz; 140 dB @ 1kHz | |||
Input Coupling | DC, AC 0.1 Hz, 1 Hz (3 Hz, 10 Hz per SW) | |||
Input Impedance | 1 MΩ (270 kΩ for AC coupling ≥ 1 Hz) in parallel with 100 pF | |||
Over-voltage Protection | In+ to In-: 50 V continuous; 200V peak (10msec) | |||
In- to GND (differential version): 3 Volt | ||||
IEPE mode | ||||
Excitation | 4, 8 or 12 mA | |||
Compliance voltage | 22 Volt | |||
Output Impedance | > 100 kΩ | |||
Sensor detection | Shortcut: < 4 Volt; Open: > 10 Volt | |||
Additional Specifications | ||||
Input connector | BNC | |||
TEDS support | IEPE mode only |
Overview
HS-HV | HS-LV | HS-ACC | HS-CHG | HS-STG | |
Connectors | BANANA | DB9 | BNC | BNC, TNC | DB9 |
Counter version | |||||
Channels per slice | 8 | ||||
Data rate / channel |
1 Ms/sec USB | ||||
Resolution | 16 bit | ||||
Bandwidth | 2 MHz | 1 MHz | 500 kHz | 500kHz CHG:200 | 1 MHz |
Voltage ranges | ±1600 V ... ±20 V | ±100V ... ±50 mV | ±10V ... ±100 mV | ±10V ...±100 mV | ±50V ... ±20 mV |
Input coupling | DC | DC, AC 1Hz (3, 10 Hz SW) | DC, AC 1Hz (3, 10 Hz SW) | DC, AC 0.1 Hz, 1 Hz, 10 Hz, 100 Hz | DC, AC 1Hz (3, 10 Hz SW) |
Sensor excitation | 2..30 V bipolar, 0..24 unipolar, max. 0.2A/2W | IEPE 4,8 mA | IEPE 4,8,12 mA | 0..20 V max. 0.8W, 0..60mA max 0.5W | |
Bridge connection |
Full | Full, ½, ¼ 350Ω, ¼ 120Ω 3, 4 wire | |||
Programmable shunt |
59.88 kΩ, 175kΩ bipolar | ||||
IEPE input | DSI-ACC | DSI-ACC | |||
Resistance | DSI20mA, DSI5A | ||||
Temperature (PTx) |
DSI-RTD | ||||
Thermocouple | DSI-TH | DSI-TH | |||
Potentionemeter | ??? | ||||
LVDT | DSI-LVDT | DSI-LVDT | |||
Charge | DSI-CHG | 100k ...1000 pC | DSI-CHG | ||
Current | ext. shunt | ext. shunt | ext. shunt | ext. shunt | |
TEDS | |||||
Isolation voltage | CATII 1000V | 1000 V | 1000 V | 1000 V | 1000 V |
Power consumption per channel | 1W/ch | 1.2W/ch | 2 W/ch | 1.2W/ch | 2W/ch |
Advanced functions |
High voltage, high bandwidth, high isolation | High sensor power and multi range | Sensor error detection, high speed | Sensor error detection in IEPE and CHG mode (injection) | High speed, supports all strain types and high input range |
HS general specifications
ADC | |
Type | 16 bit SAR |
Sampling Rate | Simultaneous 1 MS/sec |
Analog anti alias filter | Bypass or analog 100kHz 5th order |
Digital low pass filter | Software selectable |
Digital filter Characteristic | Bypass, Butterworth or Bessel |
Filter Order | 2nd , 4th, 6th or 8th |
Ratio Sample rate to Filter Freq. | From 2 to 100 |
Topology | Cascaded IIR Filter (up to 4 sections) |
HS-HV
Inputs | Voltage | |||
ADC Type | 16bit SAR | |||
Sampling Rate | Simultaneous 1 MS/sec | |||
Filtering | See "SIRIUS HS general specifications" | |||
Analogue bandwidth | 2 MHz | |||
Voltage ranges | ±1600 V, ±800 V, ±400 V, ±200 V, ±100 V, ±50 V, ±20 V | |||
Input Accuracy (see 1) | Signal frequency | Accuracy | ||
DC | ±0.03% of reading ±0.02% of range ±0.04V | |||
Up to 1kHz | ±0.03% of reading ±0.02% of range | |||
Up to 10 kHz | ±0.1% of reading ±0.05% of range | |||
Up to 100 kHz | ±2% of reading ±0.1% of range | |||
Up to 1000 kHz | ±5% of reading ±0.5% of range | |||
Typ. SNR | Bandwith | 1600 Volt | 400 V | 100 V |
2 MHz | 83 dB | 79 dB | 71 dB | |
100 kHz | 85 dB | 85 dB | 82 dB | |
10 kHz | 100 dB | 97 dB | 90 dB | |
Typ. CMR @ 50 Hz/1kHz/10 kHz | 85/75/50 dB | |||
Gain Drift | Typical 10 ppm/K, max. 40 ppm/K | |||
Offset Drift | Typical 1 mV/K + 1 ppm of range/K, max 2 mV/K + 5 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Channel Cross talk | 115 dB @ 50Hz; 90 dB @ 1kHz | |||
Input Coupling | DC | |||
Input Impedance | 10 MΩ || 2pF | |||
Protection class | CAT III 600 V; CAT II 1000 V | |||
Over-voltage Protection | In+ to In-: 1.8 kVRMS, Inx to GND: 1.4kVRMS | |||
Additional Specifications | ||||
Input connector | Banana | |||
TEDS support | NA | |||
1) 50 V Range (1.2 MHz) and 20 V range (700 kHz) have limited bandwidth |
HS-LV
Inputs | Voltage | |||
ADC Type | 16bit SAR | |||
Sampling Rate | Simultaneous 1 MS/sec | |||
Filtering | See "SIRIUS HS general specifications" | |||
Analogue bandwidth | 1 MHz (800 kHz for ranges ≤0.2V) | |||
Voltage ranges | ±100, 50, 20, 10, 5, 2, 1, 0.5, 0.2, 0.1 and 0.05 Volt | |||
Input Accuracy | Signal frequency | Accuracy | ||
DC | ±0.03% of reading ±0.02% of range ±100 μV (2mV for Ranges ≥ 10Volt) | |||
Up to 1 kHz | ±0.03% of reading ±0.02% of range | |||
Up to 10 kHz | ±0.1% of reading ±0.05% of range | |||
Up to 100 kHz | ±2% of reading ±0.1% of range | |||
Offset accuracy after Balance Amplifier | Range < 10 V: ±0.002% of range ±3 μV; Range ≥ 10 V: ±0.005% of range | |||
Typical SNR | 100 V | 5 V | 0.5 V | 0.05 V |
Bandwidth 1 MHz | 85 dB | 86 dB | 78 dB | 59 dB |
Bandwidth 100 kHz | 88 dB | 88 dB | 87 dB | 76 dB |
Bandwidth 10 kHz | > 100dB | > 100dB | 95 dB | 86 dB |
Typical CMR | 100 V | 5 V | 0.5 V | 0.05 V |
50 Hz | 70 dB | 88 dB | 102 dB | 102 dB |
400 Hz | 70 dB | 86 dB | 100 dB | 100 dB |
10 kHz | 55 dB | 70 dB | 80 dB | 80 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |||
Offset Drift | Typical 0.3 μV/K + 5 ppm of range/K, max 2 μV/K + 10 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter channel phase mismatch | 0.02° * fin [kHz] + 0.1° (5 V Range) | |||
Channel Cross talk Range | < 10 V: 120 dB @ 10kHz; Range ≥ 10 V: 95 dB @ 10kHz | |||
Input Coupling (see 1) | DC, AC 1 Hz (3 Hz, 10 Hz per SW) | |||
Input Impedance | Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ || 110pF between INx to GND | |||
Max. Common Mode Voltage | Isolated version: ±500 V | |||
Differential version: Ranges ≥ 10Volt: ±100 V; all other Ranges: ±12 V | ||||
Overvoltage Protection Range | < 10 V: 100V (200 V peak for 10msec); Range ≥ 10 V: 300 V cont. | |||
Excitation Voltage | Unipolar or Bipolar Software selectable (programmable 16 bit DAC) | |||
Excitation Level | unipolar 0 .. 24 Volt; Predefined levels: 1, 2.5, 5, 10, 12, 15, 20 and 24 VDC | |||
Exication Level | bipolar 2 .. 30 Volt; Predefined levels: 2.5, 5, 10, 12, 15, 24 and 30 VDC | |||
Accuracy | ±0.1 % ±5 mV | |||
Drift | ±50 ppm/K ±100 μV/K | |||
Stability 10% to 90% load (bipolar) | <0.01% | |||
Current limit | 200mA (2 Watt max. per Channel, 12 Watt max. per Slice) | |||
Protection | Continuous short to ground | |||
Input short, Sensor offset adjust | Software selectable | |||
Counters (only on HS-LV+ type) | 1 counter/3 digital input, fully synchronised and alarm output | |||
Counter modes | counting, waveform timing, encoder, tacho, gear tooth sensor | |||
General Counter Specifications | "See ""SIRIUS counter specification" | |||
Additional Specifications | ||||
Input connector | DSUB 9, Banana, BNC (others on request) | |||
TEDS support | Standard + DSI® adapters | |||
1) In- must be within ±10V referred to GND(iso); for Ranges ≥ 10 V the DC value of In- is not rejected |
HS-ACC
Inputs | Voltage, IEPE | |||
ADC Type | 16bit SAR | |||
Sampling Rate | Simultaneous 1 MS/sec | |||
Filtering | See "SIRIUS HS general specifications" | |||
Analogue bandwidth | 500 kHz | |||
Voltage ranges | ±10 Volt | ±5 Volt | ±1 Volt | ±0.2 Volt |
Input Accuracy | ±0.05% of reading | |||
Offset Accuracy | ±2mV | ±1mV | ±0.2mV | ±0.1mV |
Typ. SNR @ 100kHz | 89 dB | 89 dB | 86 dB | 83 dB |
Typ. CMR @ 50Hz/400Hz/1kHz | 120/96/88 dB | 126/100/92 dB | 140/110/102 dB | 140/118/110 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |||
Offset Drift | Typical 0.5 μV/K + 10 ppm of range/K, max 3 μV/K + 20 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° | |||
Channel Cross talk | 120 dB @ 1kHz; 100 dB @ 10kHz | |||
Input Coupling | DC or AC (1Hz) | |||
Input Impedance | 1 MΩ | |||
Overvoltage Protection | 50 V continuous; 200V peak (10msec) | |||
IEPE mode | ||||
Excitation | 4 or 8mA | |||
Compliance voltage | 25 Volt | |||
Output Impedance | >100 kΩ | |||
Sensor detection | Shortcut: <4Volt; Open: > 19Volt | |||
Counters (HS-ACC+ type only) | 1 counter/3 digital input, fully synchronised with analogue data | |||
Counter Modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
General Counter Specifications | See "SIRIUS counter specification" | |||
Additional Specifications | ||||
Input connector | BNC | |||
TEDS support | IEPE mode only |
HS-CHG
Inputs | Voltage, IEPE, Charge | ||||
ADC Type | 16bit SAR | ||||
Sampling Rate | Simultaneous 1 MS/sec | ||||
Filtering | See "SIRIUS HS general specifications" | ||||
Analogue bandwidth | 500 kHz (200 kHz for charge) | ||||
Voltage ranges | ±10, ±5, ±2, ±1, ±0.5, ±0.2, ±0.1 Volt | ||||
Input Accuracy | Signal frequency | Accuracy | |||
DC | ±0.05% of reading ±0.02% of range ±50μV | ||||
up to 10kHz | ±0.1% of reading ±0.05% of range | ||||
up to 100kHz | ±2% of reading ±0.1% of range | ||||
Typ. SNR | Bandwidth/Range → | 10 V | 5 V | 1 V | 0.1 V |
1 MHz | 88 dB | 87 dB | 85 dB | 68 dB | |
100 kHz | 89 dB | 89 dB | 88 dB | 83 dB | |
10 kHz | > 100 dB | > 100 dB | > 100 dB | 92 dB | |
Typical CMR | 50Hz/1kHz | >140/120dB | >140/124dB | >140/126dB | >140/126dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | ||||
Offset Drift | Typical 0.5 μV/K + 10 ppm of range/K, max 3 μV/K + 20 ppm of range/K | ||||
Gain Linearity | <0.02% | ||||
Inter Channel Phase-mismatch | 0.02° * fin [kHz] + 0.1° | ||||
Channel Cross talk | 110 dB @ 1kHz; 90 dB @ 10kHz | ||||
Input Coupling | DC or AC (0.1 Hz, 1 Hz, 10 Hz or 100 Hz) | ||||
Input Impedance | 1 MΩ / 100pF | ||||
Overvoltage Protection | 50 V continuous; 200V peak (10msec) | ||||
IEPE mode | |||||
Excitation | 4 or 8mA | ||||
Compliance voltage | 25 Volt | ||||
Output Impedance | >100 kΩ | ||||
Sensor detection | Shortcut: <4Volt; Open: > 19Volt | ||||
Charge ranges | ±100 000, 50 000, 20 000, 10 000, 5000, 2000, 1000 pC | ||||
Input Accuracy | ±0.5% of reading ±0.05% of range ±2 pC | ||||
Input Coupling | 0.01 Hz, 0.03 Hz, 0.1 Hz, 0.5 Hz, 1 Hz, 10 Hz or 100 Hz | ||||
Counters (only on HS-CHG+ type) |
1 counter/3 digital input, fully synchronised with analogue data | ||||
Counter Modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | ||||
General Counter Specifications | See "SIRIUS counter specification" | ||||
Additional Specifications | |||||
Input connector | BNC (others on request) | ||||
TEDS support | IEPE mode only |
HS-STG
Inputs | Voltage, full bridge strain, half bridge strain, quarter bridge strain (120Ω and 350Ω), resistance, temperature | |||
ADC Type | 16bit SAR | |||
Sampling Rate | Simultaneous 1 MS/sec | |||
Filtering | See "SIRIUS HS general specifications" | |||
Analogue bandwidth | 1 MHz (800 kHz for ranges ≤0.2V) | |||
Voltage ranges | ±50, 20, 10, 5, 2, 1, 0.4, 0.2, 0.1, 0.04 and 0.02 Volt | |||
Input Accuracy | Signal frequency | Accuracy | ||
DC | Range < 10 V: ±0.03% of reading ±0.04% of range ±10μV | |||
Range ≥ 10 V: ±0.05% of reading ±0.01% of range ±5 mV | ||||
Up to 1 kHz | ±0.03% of reading ±0.02 of range | |||
Up to 10 kHz | ±0.1% of reading ±0.05% of range | |||
Up to 100 kHz | ±2% of reading ±0.1% of range | |||
Up to 500 kHz | ±10% of reading ±0.5% of range | |||
Offset accuracy after Balance Amplifier | Range < 10 V: ±0.002% of range ±3 μV; Range ≥ 10 V: Not performed | |||
Typical SNR | 50 V | 5 V | 0.2 V | 0.02 V |
Bandwidth 1 MHz | 87 dB | 88 dB | 81 dB | 63 dB |
Bandwidth 100 kHz | 88 dB | 88 dB | 85 dB | 74 dB |
Bandwidth 10 kHz | >100 dB | >100 dB | 94 dB | 84 dB |
Typical CMR | 50 V | 5 V | 0.2 V | 0.02 V |
50 Hz | 70 dB | 88 dB | 102 dB | 102 dB |
400 Hz | 70 dB | 86 dB | 100 dB | 100 dB |
10 kHz | 55 dB | 70 dB | 80 dB | 80 dB |
Gain Drift | Typical 10 ppm/K, max. 30 ppm/K | |||
Offset Drift | typical 0.3 μV/K + 15 ppm of range/K, max 2 μV/K + 40 ppm of range/K | |||
Gain Linearity | <0.02% | |||
Inter channel phase mismatch | 0.02° * fin [kHz] + 0.1° (5 V Range) | |||
Channel Cross talk | Range < 10 V: 120 dB @ 10kHz; Range ≥ 10 V: 95 dB @ 10kHz | |||
Input Coupling (see 1) | DC, AC 1 Hz (3 Hz, 10 Hz per SW) | |||
Input Impedance | Range < 10 V: 10 MΩ; Range ≥ 10 V: 1 MΩ between INx to GND | |||
Max. common mode voltage | Isolated version: ±500 V | |||
Differential version: Ranges ≥ 10Volt: ±60 V; all other Ranges: ±12 V | ||||
Over voltage Protection | Range < 10 V: 100V (200 V peak for 10msec); Range ≥ 10 V: 300 V cont. | |||
Excitation Voltage | Free programmable (16 Bit DAC) | |||
Predefined levels | 0, 1, 2.5, 5, 10, 15 and 20 VDC | |||
Accuracy | ±0.05 % ±2 mV | |||
Drift | ±10 ppm/K ±100 μV/K | |||
Load stability 0% to 100% load | <0.01% | |||
Line regulation over 20Ω of change | < 0.005% @ 120Ω load | |||
Noise @ 10 Volt / 350 Ω | < 200 μVrms@10 kHz BW | |||
Sense Impedance to Exc / to GND | 100 kΩ / 100MΩ | |||
Current limit | 100mA (max. 800mW) | |||
Protection | Continuous short to ground | |||
Input short, Sensor offset adjust | Software selectable | |||
Excitation Current | Free programmable (16 Bit DAC) | |||
Predefined levels | 0.1, 1, 2, 5, 10, 20 and 60 mADC | |||
Accuracy (>10 mA) | 0.1% ±2μA [0.5% ±50 μA] | |||
Drift (>10 mA) | 15 ppm/K [100 ppm/K] | |||
Compliance voltage | 20 Volt, max. 300 mW | |||
Output Impedance | >1 MΩ | |||
Bridge Connection Types | full bridge, ½ bridge and ¼ bridge (3- or 4-wire) | |||
Ranges | 2 mV/V…1000 mV/V free programmable | |||
Internal Bridge Completion | ½ bridge and ¼ bridge 120Ω and 350Ω | |||
Bridge Completion Accuracy | 0.05 %; TCR: 5 ppm/K (others on request) | |||
Internal Shunt Resistor | 59.88 kΩ and 175 kΩ, bipolar (to +Exc and -Exc) | |||
Typ. Shunt Resistor Accuracy | 0.05 %; TCR: 10 ppm/K (others on request) | |||
Sensor Balance Range | 220% of Range (70% for input Range ≥ 5Volt) | |||
Input Short, Sensor Offset Adjust | Software selectable | |||
Counters (only on HS STG+) | 1 counter/3 digital input, fully synchronised and alarm output | |||
Counter modes | counting, waveform timing, encoder, tacho, gear-tooth sensor | |||
General Counter Specifications | "See ""SIRIUS counter specification" | |||
Additional Specifications | ||||
Input connector | DSUB 9 (others on request) | |||
TEDS support | Standard + DSI® adapters | |||
1) In- must be within ±10V referred to GND(iso); for Ranges ≥ 10V the DC value of In- is not rejected |